当前位置:汉派瑞流体 >> 公司动态 >> 行业资讯 >> 浏览文章行业资讯

气动增压泵的保养与维修/气体增压泵
作者:admin | 关键词:气动增压,增压泵,保养,维修,气体 | 添加日期:2020年02月11日 | 浏览次数:

气动增压泵的保养与维修/气体增压泵/气液增压泵
气动增压泵的保养与维修/气体增压泵

Maintenance and repair of pneumatic booster pump/gas booster pump/gas-liquid booster pump

1.安装:安装过程中,要避免杂物进入驱动气口气口和进口,避免换向不灵活或进口单向阀失效。

1. Installation: during the installation process, it is necessary to avoid debris entering the air port and inlet of the driving air port, and avoid unflexible reversing or failure of the inlet one-way valve.

2.驱动气体:请使用清洁的气源,以保证泵能持续稳定的工作,驱动气体要求颗粒<5um,泵在装配时,所有运动部分已经抹有适量润滑油,一般不再需要润滑,如长期使用干燥的压缩气体驱动,如前端配有冷干机、吸干机。建议在泵的驱动口加配油雾器,油杯内加入适量的润滑油,进行油雾润滑。

2. Drive gas: please use a clean air source to ensure the continuous and stable operation of the pump. Drive gas requires particles <5um.It is recommended to add oil mist dispenser at the pump's driving port and add appropriate amount of lubricating oil in the oil cup for oil mist lubrication.

3.连接管路:根据泵的输出压力,请选择合适的出口连接管路,确保承受泵的最大输出压力。

3. Connect the pipeline: according to the output pressure of the pump, please choose the appropriate outlet to connect the pipeline to ensure that it can bear the maximum output pressure of the pump.

4.气体增压泵入口压力:入口压力越大,流量也随之增大,单级增压泵,需要一定的预压才能达到理论最大输出压力。双级增压泵,入口压力要求1-12bar,入口压力不允许超过10bar,建议<8bar。确保泵的使用寿命。

4. Inlet pressure of gas booster pump: the greater the inlet pressure is, the larger the flow will be. For single-stage booster pump, a certain amount of prepressure is required to reach the theoretical maximum output pressure.For two-stage booster pump, inlet pressure is required to be 1-12bar, inlet pressure is not allowed to exceed 10bar, and it is recommended to be <8bar.Ensure the service life of the pump.

5.最小驱动气压:该泵的最小驱动压力为1.5-2bar。

5. Minimum driving pressure: the minimum driving pressure of the pump is 1.5-2bar.

6.接口尺寸很重要:请确认所安装的螺钉和管是否适合泵的范围,为保证液泵能获得理想的流量和压力,不能减少泵的尺寸。

6.Interface size is very important: please confirm whether the installed screws and tubes are suitable for the scope of the pump, in order to ensure that the fluid pump can obtain the ideal flow and pressure, not to reduce the size of the pump.

7.气体增压泵的操作温度:标准温度范围为-20度到80度,液泵最大操作温度可达60度,短时操作时,最大操作温度可达80度。

7.Operating temperature of gas booster pump: the standard temperature range is -20 ℃ to 80 ℃, the maximum operating temperature of liquid pump can reach 60 ℃, and the maximum operating temperature can reach 80 ℃ for short operation.


版权所有 Copyright 2013 济南汉派瑞流体设备有限公司 济南市济阳区济北开发区智造小镇F3栋
电话:0531-88621016 邮箱:hipressure@163.com :鲁ICP备11001027号-2 技术支持:济南网站建设